Insulation Plaster – Thermonetper https://www.thermonetper.com Wed, 31 Jul 2024 07:54:49 +0000 en-US hourly 1 https://wordpress.org/?v=6.6.1 Exterior Insulation Plaster 50 L https://www.thermonetper.com/en/product/exterior-insulation-plaster-50-l/ https://www.thermonetper.com/en/product/exterior-insulation-plaster-50-l/#respond Wed, 10 Jul 2024 21:22:11 +0000 https://www.thermonetper.com/?post_type=product&p=15654 Provide perfect insulation against all seasonal effects with a SINGLE COAT APPLICATION for year-round use. ]]>

FIELDS OF USE
It is used directly on the exterior walls of the buildings, columns and beams, on rough and fine plaster, brick, pumice bloc. Primer, must be used necessarily on concrete, gas concrete and painted surfaces.

SURFACE PREPARATION
Blistered paint and spaced plasters are scraped off the surface. 4-5 notches per 10 cm2 press on painted surfaces. The application surface should be cleaned from dust. Priming must be done on painted surfaces.

APPLICATION
Laths that determine the thickness are adhered to the prepared surfaces. Between two laths, is filled with a steel trowel or plasterer trowel and gauged. Following the first dry (~ 1-2 hours later), the slats are removed from the surface and the spaces are filled and the pattern is drawn. if is dry when touched, (12-24 hours later) decorative plaster is drawn. No foreign matter should be added to the prepared mixture. (Lime, Plaster, Cement, etc.)

APPLICATION DETAILS
In manual application, it should be mixed with ~ 11-12 liters of water with low speed (400-600 rev/min) drill for 3-4 minutes. In machine application, it should be pumped to the surface by mixing with 11-12 liters of water in average. When the desired thickness is reached, it should be allowed to dry.

APPLICATION CONDITIONS
Application surface and ambient temperature should be above 5 °C. Considering excessive moisture loss at temperatures above 35 °C, mixing water should be increased and the surface should be kept moist by wetting for 1 day after the surface hardening phase.

ISSUES TO BE CONSIDERED
Avoid application under strong wind or sun. The time increases at low temperatures and the time decreases at high temperatures. It should not be applied on frozen, melting or freezing surfaces within 24 hours. Appropriate plaster mesh should be used at different material junctions and points where movement may be considered.

STORAGE TRANSPORT
Protect from frost, rain and other weather conditions. 70 Bags in 1 pallet is 3.500 L.

ENVIRONMENTAL IMPACTS
Not classified as dangerous.

]]> https://www.thermonetper.com/en/product/exterior-insulation-plaster-50-l/feed/ 0 Interior Insulation Plaster 50 L https://www.thermonetper.com/en/product/interior-insulation-plaster-50-l/ https://www.thermonetper.com/en/product/interior-insulation-plaster-50-l/#respond Wed, 10 Jul 2024 21:19:21 +0000 https://www.thermonetper.com/?post_type=product&p=15646 Provide perfect insulation against all seasonal effects with SINGLE COAT APPLICATION for year-round use. ]]>

FIELDS OF USE
It can be used as between floors as screed insulation.

SURFACE PREPARATION
The application surface floor covering, must be cleaned from dust first. Prevent adhesion materials such as paint and oil should be cleaned and the preparation should be completed.

APPLICATION
Consistently prepared floor screed is applied in a single layer with a steel trowel or plaster pump on a slightly damp surface and gauge is applied. No foreign material should be added to the prepared mixture. (Lime, Gypsum, Cement etc.)

APPLICATION DETAILS
In manual application, it should be mixed with an average of 8-10 liters of water with a low speed drill for 3-4 minutes, poured onto the floor and allowed to dry. In machine application, it should be pumped to the surface by mixing with an average of 8-10 liters of water. When the desired thickness is reached, it should be allowed to dry.

APPLICATION CONDITIONS
Application surface and ambient temperature should be above 5 °C. Considering excessive moisture loss at temperatures above 35 °C, mixing water should be increased and the surface should be kept moist by wetting for 2 days after the surface hardening phase.

ISSUES TO BE CONSIDERED
Avoid application under strong wind or sun. The time increases at low temperatures and the time decreases at high temperatures. It should not be applied on frozen, melting or freezing surfaces within 24 hours. Appropriate plaster mesh should be used at different material junctions and points where movement may be considered.

STORAGE TRANSPORT
Protect from frost, rain and other weather conditions. 70 Bags in 1 pallet is 3.500 L.

ENVIRONMENTAL IMPACTS
Not classified as dangerous.

]]> https://www.thermonetper.com/en/product/interior-insulation-plaster-50-l/feed/ 0 Insulated Light Screed 50 L https://www.thermonetper.com/en/product/insulated-light-screed-50-l/ https://www.thermonetper.com/en/product/insulated-light-screed-50-l/#respond Wed, 10 Jul 2024 21:17:07 +0000 https://www.thermonetper.com/?post_type=product&p=15638 ]]>

FIELDS OF USE
It can be used as between floors as screed insulation.

SURFACE PREPARATION
The application surface floor covering, must be cleaned from dust first. Prevent adhesion materials such as paint and oil should be cleaned and the preparation should be completed.

APPLICATION
Consistently prepared floor screed is applied in a single layer with a steel trowel or plaster pump on a slightly damp surface and gauge is applied. No foreign material should be added to the prepared mixture. (Lime, Gypsum, Cement etc.)

APPLICATION DETAILS
In manual application, it should be mixed with an average of 8-10 liters of water with a low speed drill for 3-4 minutes, poured onto the floor and allowed to dry. In machine application, it should be pumped to the surface by mixing with an average of 8-10 liters of water. When the desired thickness is reached, it should be allowed to dry.

APPLICATION CONDITIONS
Application surface and ambient temperature should be above 5 °C. Considering excessive moisture loss at temperatures above 35 °C, mixing water should be increased and the surface should be kept moist by wetting for 2 days after the surface hardening phase.
ISSUES TO BE CONSIDERED
Avoid application under strong wind or sun. The time increases at low temperatures and the time decreases at high temperatures. It should not be applied on frozen, melting or freezing surfaces within 24 hours. Appropriate plaster mesh should be used at different material junctions and points where movement may be considered.

STORAGE TRANSPORT
Protect from frost, rain and other weather conditions. 70 Bags in 1 pallet is 3.500 L.

ENVIRONMENTAL IMPACTS
Not classified as dangerous.

]]> https://www.thermonetper.com/en/product/insulated-light-screed-50-l/feed/ 0